Campbell Hausfeld Airless Paint Sprayer Won Prime

Campbell Hausfeld Airless Paint Sprayer Won Prime Manuals Included With#

Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference. Protect yourself and others by observing all safety information. Read carefully before attempting to assemble, install, operate or maintain the product described. If reversible tip is used, rotate spray tip to CLEAN position.Operating Instructions and Assembly Instructions Airless Paint Sprayers Cleanup for Changing Paints or Temporary Storage for More Than One Night (Continued) 17.1 Operating and Assembly Instructions Please read and save these instructions. Turn Prime/ Spray Control to SPRAY (knob is vertical) 9. Turn prime/spray control to SPRAY/ ROLL position.

NOTE: Guns pictured in illustrations may be different than the one included with your unit. These sprayers are also powerful and versatile enough to be used with a variety of options (roller attachment, extra lengths of hose, etc.) to make it an even more efficient tool. These superb pneumatic paint sprayer come with unbeatable discount offers.2 Operating Instructions and Assembly Instructions Airless Paint Sprayers Table of Contents Description Safety Guidelines General Safety Information Preparation Spraying Instructions Cleanup Storage Maintenance Troubleshooting Miscellaneous Information Warranty Description Airless paint sprayers are capable of spraying a wide variety of latex, oilbased, and alkyd paints, as well as stains, preservatives and other nonabrasive finishes. You can also try reaching out to Campbell Hausfeld Tech at 80 to see what their recommendations are for The top-notch pneumatic paint sprayer on Alibaba.com redefine spraying efficacy.

Notice indicates NOTICE important information, that if not followed, MAY cause damage to equipment. Caution indicates a! CAUTION potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. Warning indicates! WARNING a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Danger indicates! DANGER an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. To help recognize this information, observe the following symbols. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS.

Campbell Hausfeld Airless Paint Sprayer Won Prime Manuals Included With

Read all manuals included with this product MANUAL carefully. General Safety Information 1. Damage may result in bursting and cause injury or property damage. Do not operate! WARNING unit if damaged during shipping, handling or use. Make sure to tighten fittings, bolts, etc., before putting unit into service.

Can Do Not Tip Spray Coating Use Use Size ** Pressure Oil Base Stain x psi Wood Sealer x psi Concrete Sealer x psi Enamel x psi Varnish x psi Non-Metal Flake Aluminum Paint x psi Vinyl Latex Paint x psi Vinyl / Acrylic Latex Paint x psi Acrylic Latex Paint x psi Oil Base Paint x psi Oil and Water Based Primer x psi V. Keep visitors away and NEVER allow children or pets in the work area. Be certain mask or respirator will provide necessary protection against inhalation of harmful vapors. Always wear a mask or respirator and eye protection when painting.

ELECTRICAL SHOCK HAZARD: Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and in the United States, the Occupational Safety and Health Act (OSHA). When spraying and cleaning, always follow the instructions and safety precautions provided by the material manufacturer (Refer to MSDS). To avoid injury and damage to the workpiece, do not aim the spray gun at any dust or debris. Always work in a clean environment. Do not smoke or eat when spraying paint, insecticides, or other flammable substances. 23 Operating Instructions and Assembly Instructions Airless Paint Sprayers General Safety Information (Continued) 4.

Do not modify any of the electrical components of this equipment. Only qualified electricians or service personnel should perform maintenance on the electrical components of this equipment. If the power receptacles available will not fit this equipment s power cord, then have an appropriate power receptacle installed by a certified electrician.

APPROPRIATE EXTENSION CORD GAUGE FOR GIVEN LENGTHS SKIN INJECTION HAZARD: High pressure spray can inject toxins into blood stream. Check with a qualified electrician or service person if the grounding instructions are not completely understood or you are in doubt as to whether the equipment is properly grounded. If using an extension cord, use only grounded three wire extension cords that are in good condition.

Use only Campbell Hausfeld replacement parts rated at 3000 psi or higher. This system is capable of producing 3000 psi. Length of Cord! WARNING! WARNING Gauge Never try to stop leaks with any part of your body. Refer to Material Safety Data Sheets (MSDS) of spray material for details. Always spray in a well ventilated area to prevent health and fire hazards. Use a face mask/respirator and protective clothing when spraying.

Do not remove spray tip while cleaning pump. Always engage trigger lock when not spraying. See Maintenance section for inspection procedures. Ensure trigger lock is functioning properly.

Motor will restart without warning, after cooling. Motor is equipped with an automatic thermal overload. Do not use pliers to tighten or loosen high pressure connections. Ensure tightness of high pressure connections. Remove spray tip from gun to clean tip guard. Do not clean spray tip while it is attached to the spray gun.

Turn power switch to OFF position. Turn the pressure control to LOW PRESSURE/HYDRAULIC BLEEDING position. Turn the Prime/Spray Control to the PRIME position. Before servicing or resting: 1.

Motors, electrical equipment and controls can cause electrical arcs that will ignite a flammable gas or vapor. 34 Operating Instructions and Assembly Instructions Airless Paint Sprayers General Safety Information (Continued) Do not spray flammable materials in vicinity of open flame or near ignition sources. A partial example list of unacceptable cleaning solvents are low flash napha, mek, acetone, alcohol and toluene). The above procedure MUST be followed.! WARNING FIRE OR EXPLOSION HAZARD: Do not use solvents with flash points less than 70 F (21 C) to clean this equipment (examples of acceptable cleaning solvents are water, mineral spirits, lacquer thinner, Xylene and high flash napha. Simply turning off the pump motor will not relieve pressure from system.

Remove all ignition sources (i.e. Keep doors and windows open. Keep spraying area well ventilated. Do not use fuels to clean this equipment. Using these materials could result in death or serious injury. Do not spray acids,! WARNING corrosive materials, toxic chemicals, fertilizers or pesticides.

Always use a 3-wire grounded extension cord and power receptacle. Always ground the pump and spraying surface. Airless spraying can cause static electricity.

Each pump is tested at the factory with a fluid that Prime/Spray Valve Suction Bell Assembly Housing Pressure Valve Motor must be flushed from the system prior to painting. It is important that the painting equipment is flush/tested EACH time a new job is started. Following these instructions will significantly increase the likelihood of having a positive paint experience.

Push outlet prime button three times to ensure outlet valve is moving freely. 45 Operating Instructions and Assembly Instructions Airless Paint Sprayers Preparation (Continued) DO NOT ATTACH THE SUCTION ASSEMBLY UNTIL INSTRUCTED TO DO SO IN STEP Remove inlet valve cap and with your smallest finger, push on inlet valve stem to ensure it moves freely. Refer to the paint manufacturer s recommendations for cleaning fluids. Use the solvent which will be used to clean the equipment.

Turn prime/spray control to SPRAY position. Allow the fluid to circulate for one minute to ensure all air has been exhausted from the pump. In a few seconds, cleaning solvent will begin to move up through the tube. Turn power switch to the ON position. Turn prime/spray control to the PRIME position. Turn pressure to HIGH (completely clockwise).